Pig Flooring Systems and Components for Commercial Farms
Honde supplies pig flooring components for commercial farm construction, equipment distribution, and replacement projects. Its product range includes fiberglass-reinforced plastic (FRP) T-profile beams, cast iron leakage plates for sows, and hog cast iron slats.
Each component serves a different function within a pig flooring system. FRP beams provide structural support, while cast iron floor sections form the slatted or open-floor surfaces specified in the housing design. Selecting the right components requires attention to the floor layout, support structure, animal housing stage, and manure handling arrangement.
Whether you are building a new pig house or replacing existing flooring, Honde can review your product requirements, drawings, dimensions, and order quantity.
-
![Fiberglass T Profile Beams]()
Fiberglass T Profile BeamsFiberglass T Profile Beams are structural support components made from fiberglass-reinforced plastic (FRP) for livestock flooring systems. Honde manufactures these beams through the pultrusion... -
![Cast Iron Leakage Plate for Sows]()
Cast Iron Leakage Plate for SowsCast Iron Leakage Plate for Sows is a cast iron slatted flooring component designed for sow housing in pig farms. Honde specifies a 1 cm gap with rounded, smooth inner edges without burrs. The... -
![Hog Cast Iron Slat]()
Hog Cast Iron SlatHog Cast Iron Slat is a slatted flooring component designed for pig housing facilities. Honde identifies ductile cast iron as the material and describes the product as having a smooth, firm...
Pig Flooring Products at a Glance
|
Product |
Main Material |
Primary Function |
Key Purchasing Considerations |
|
Fiberglass T-Profile Beams |
Fiberglass-reinforced plastic (FRP) |
Flooring support members |
Beam profile, length, support spacing, and design loads |
|
Cast Iron Leakage Plate for Sows |
Cast iron |
Floor sections for sow housing |
Opening dimensions, panel size, edge finish, and installation compatibility |
|
Hog Cast Iron Slat |
Cast iron; the product description specifies ductile cast iron |
Slatted flooring sections |
Material grade, slot arrangement, panel dimensions, and supporting structure |
How to Select Pig Flooring Components
The right specification depends on the intended housing area, structural arrangement, drainage requirements, and compatibility between components.
Floor Layout and Support Structure
Prepare the following information before requesting a quotation:
- Floor dimensions: Length, width, and layout of the pen or floor section.
- Support arrangement: Existing support type and spacing, or the planned structure for a new installation.
- Component dimensions: Required beam profiles, floor panel sizes, and installation clearances.
- Connections: Details of how the components fit together.
- Replacement information: Existing product measurements and installation photographs, where applicable.
A component may meet its material requirements but still be unsuitable if its dimensions or support arrangement do not match the installation.
Animal Category and Floor Location
Different housing areas may require different flooring configurations. Identify the intended application when requesting a quotation.
|
Application |
Key Considerations |
|
Farrowing and sow housing |
Opening geometry, surface finish, and animal contact areas |
|
Nursery pens |
Floor dimensions and compatibility with the housing design |
|
Grow-finish housing |
Panel arrangement, support structure, and applicable design loads |
|
Other pig housing areas |
Intended animal category and project-specific requirements |
Final selection should account for the applicable animal welfare and construction requirements in the project location.
Manure Handling and Cleaning
Floor openings must match the underlying manure collection or drainage arrangement.
Confirm the following:
- Opening dimensions and layout.
- Position of the floor sections above the manure collection area.
- Access for routine cleaning and maintenance.
- Exposure to moisture and manure when selecting support materials.
Evaluate the beams and floor sections as parts of one system rather than as separate products.
Technical Specifications to Confirm Before Ordering
Use the following checklists to establish the required specifications for each product.
FRP T-Profile Beams
- Profile shape and cross-sectional dimensions.
- Required beam length and dimensional tolerances.
- Resin and fiberglass reinforcement specifications, where required.
- Support spacing and connection details.
- Applicable design loads and verified load or span data.
- Material documentation and inspection requirements, if applicable.
Structural suitability must be established for the actual installation rather than inferred from material descriptions alone.
Cast Iron Leakage Plates and Slats
- Cast iron material grade and relevant documentation.
- Panel length, width, thickness, and overall dimensions.
- Slot or gap width and opening arrangement.
- Surface finish, edge condition, and applicable surface treatment.
- Connection details and compatibility with the support structure.
- Dimensional tolerances and acceptance criteria.
For sow leakage plates, confirm the listed 1 cm gap against the approved drawing. For hog cast iron slats, verify the slot arrangement and panel dimensions against the intended floor layout.
Compatibility Between Components
When purchasing beams and floor sections together, confirm that:
- Beam spacing matches the specified panel arrangement.
- Support and connection details are compatible.
- Adjacent floor sections fit together as intended.
- Required installation clearances are maintained.
- All components follow the same approved drawing or specification.
For customized projects, the approved drawing should serve as the reference for production and repeat orders.
Honde's product information describes the pultrusion process used for its FRP beams and the material and surface characteristics of its cast iron flooring products.
Before production, Honde and the buyer should agree on the approved drawings, material specifications, dimensional tolerances, and applicable inspection criteria.
FRP Beam Verification
- Confirm the specified profile, dimensions, and length.
- Establish the applicable dimensional checks.
- Identify the technical data required for structural evaluation.
- Agree on any material documentation required for the order.
Cast Iron Component Verification
- Confirm the specified material grade and panel dimensions.
- Review opening geometry and surface finish requirements.
- Establish the dimensional inspection and acceptance criteria.
- Identify any required material records or surface treatment specifications.
Order Documentation
Depending on the project requirements, the agreed documentation may include:
- Approved technical drawings and dimensional specifications.
- Applicable material documentation.
- Dimensional inspection records.
- Product acceptance criteria.
- Packaging and labeling requirements.
Confirm the available documentation and inspection arrangements with Honde before ordering. Material and performance claims should be supported by relevant product records.
Customized Pig Flooring Components for Wholesale Orders
Honde accepts customization inquiries for pig flooring products. Buyers can provide drawings, reference photographs, samples, or dimensional requirements for review.
The available customization options depend on the selected product and should be confirmed before ordering.
Information Required for a Customized Order
|
Information |
What to Provide |
|
Product type |
FRP T-profile beams, cast iron leakage plates for sows, hog cast iron slats, or a combination |
|
Dimensions |
Required profile, length, width, thickness, and opening measurements, as applicable |
|
Project layout |
Floor plan, support spacing, and installation arrangement |
|
Quantity |
Required quantity for each product or specification |
|
Delivery destination |
Country and delivery port or address |
|
Special requirements |
Material documents, inspection criteria, packaging, labeling, or other order-specific conditions |
For repeat purchases, an approved drawing and written specification provide a consistent reference for subsequent orders.
Before production, confirm the final specifications, customization feasibility, lead time, packaging, shipping arrangements, and commercial terms. Any proposed changes to dimensions or materials should be reviewed and approved before manufacturing begins.
As one of the most professional pig flooring system manufacturers and suppliers in China, we also support customized service. We warmly welcome you to wholesale advanced pig flooring system for sale here from our factory. If you have any enquiry about cooperation, please feel free to email us.
